We are ready to take your call
Tel: 00 44 (0)191 250 4610
Fax: 00 44 (0)191 250 1471
Tel: 00 44 (0)191 250 4610
Fax: 00 44 (0)191 250 1471
Kjellberg PA-S25W
Plasma cutting unit for manual and mechanized cutting.
Plasma cutting of all electrically conductive materials up to 25 mm (max.) with water cooled hand and machine torches.
Large variety of application:
Kjellberg plasma torches PB-S25 WH and PB-S45 WH can be reset from the version for plasma cutting to the application for plasma gouging and vice versa in a few seconds.
There need to be replaced nozzle and protection cap only. With this concept a high availability of the system is guaranteed.
Compared to gouging with carbon electrodes, a host of technological advantages result, i.e.:
Technical data:
Plasma cutting of all electrically conductive materials up to 25 mm (max.) with water cooled hand and machine torches.
- Manual or mechanised cutting with air, O2, Ar/H2, Ar/H2/N2 or Ar/H2 as plasma gases Ar/N2
- Even suitable for plasma gouging.
Large variety of application:
- Application of water cooled machine or hand torches
- Standard torches with 6 or 10 m hose parcel
- In connection with plasma ignition box and hose parcel extensions working area increased up to 50 m
- The gas mixing unit ensures precise and reproducible gas mixtures
- HF protected torches and hose parcel extensions for CNC controlled guiding systems
- By changing only the cathode - nozzle system the torches are suitable for all plasma gases
- On customer's request special torch models are available - 60° and 90°, short shank, etc.
- Fast change-over from cutting to gouging process
- By FineFocus principle with Double Straight effect and up to six times higher cutting speed compared to gas cutting (depending on material thickness)
- High-voltage ignition for pilot arc start
- Running cutting start and running piercing possible, no reference point necessary
- Optimal cutting current adaptation to the cutting job
- XL-Life system for the plasma gas O2
- Through a direct and extremely effective water cooling of the parts and up to five times higher life of nozzles and cathodes can be achieved
- Soft start circuit increases the life time of nozzles and cathodes
- Excellent cutting quality of both cutting surfaces
- Small kerfs, minimal material loss, low pollution by FineFocus plasma principle with Double-Straight effect
- Flexible plasma gas selection ensures optimal results on all metals
Kjellberg plasma torches PB-S25 WH and PB-S45 WH can be reset from the version for plasma cutting to the application for plasma gouging and vice versa in a few seconds.
There need to be replaced nozzle and protection cap only. With this concept a high availability of the system is guaranteed.
Compared to gouging with carbon electrodes, a host of technological advantages result, i.e.:
- no effected zone of the material
- no grinding
- lower heat penetration and therefore lower warpage
- good observation of the process performance
- noise level and smoke accumulation reduction
Technical data:
| Mains voltage | (V) | 3x230 / 400 / 500(50 Hz) |
| Fuse, slow | (A) | 50 / 32 / 25 |
| Connecting power (75% d.c. / 100% d.c.) |
(kVA) | 21 / 15 |
| Protection class | - | IP 22 |
| Insulation class | - | F |
| Open circuit voltage | (V) | 330(DC) |
| Cutting current | (A) | 25 / 45 / 70 |
| Cutting current at 75 % d.c. at 100 % d.c. |
(A) |
70 45 |
| Cutting thickness - maximum - recommended |
(mm) | 25 (material depending) 18 (material depending) |
| Plasma gases | - | Ar/H2, Ar/H2/N2, Ar/N2, Air, O2 |
| Cooling | - | Fluid (Kjellfrost) |
| Ignition | - | High voltage |
| Weight | (kg) | 168 |
| Dimensions L x W x H | (mm) | 920 x 630 x 960 |
